Buffalo NAS-Central Forums

Welcome to the Linkstation Wiki community
It is currently Sun May 27, 2018 12:27 pm

All times are UTC+01:00




Post new topic  Reply to topic  [ 38 posts ]  Go to page Previous 1 2 3 Next
Author Message
PostPosted: Thu Aug 30, 2012 10:59 pm 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
I use transmission ;)

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Top
   
PostPosted: Mon Sep 03, 2012 12:41 am 
Offline
Newbie

Joined: Fri Sep 12, 2008 4:01 am
Posts: 10
Stonie,
Your tarball worked quite nicely on my KuroHG. I did have to mess around with some directories and rights to support transmission-daemon and nasuser.

I was about to try it on a LS1 when I noticed that the kuroboxHD.dtb file, in the boot directory, was the old version. Did you try it on this hardware?

Thx
Tom


Top
   
PostPosted: Mon Sep 03, 2012 10:52 am 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
Hi Tom,

I don't have a HD... but ramuk got this image working on a HD... you may need to recompile the dtb file for the HD but I would just run with the HG one to start with, you may find it works. (someone correct me if I'm wrong - but I think the differences became redundant at some point? if I remember correctly?)

As for transmission and nasuser... yeah after an update mine stopped working too. its a bit of a pain to get going because transmission is poor when it comes to logging. I hope it didn't cause you too much pain!
Having samba and transmission share a user is pretty much essential for a nice user friendly nas. So I think the pain is worth it.

Please post back here with your results on the HD! ;)

Cheers,
Stonie.

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Top
   
PostPosted: Sun Sep 09, 2012 11:24 am 
Offline
Newbie

Joined: Thu Dec 06, 2007 9:58 am
Posts: 22
Is this kernel support iptables ?

Code:
# modprobe iptables
FATAL: Module iptables not found.


Top
   
PostPosted: Sun Sep 09, 2012 11:52 am 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
Thats pretty conclusive... you will need to recompile for that, sources and config file are in the tarball to make your life easy.

I will add it next time i compile. thanks for pointing it out.

Regards,
Stonie.

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Top
   
PostPosted: Thu Sep 13, 2012 12:57 pm 
Offline
Newbie

Joined: Thu Dec 06, 2007 9:58 am
Posts: 22
I found the error message in dmesg when system reboot...
--
Sep 11 00:23:29 Wheezy-LS kernel: Inspecting /usr/src/linux/System.map
Sep 11 00:23:29 Wheezy-LS kernel: Cannot find map file.
--

I found the answer below after google
http://www.linuxforums.org/forum/kernel ... m-map.html

Is that correct?


Top
   
PostPosted: Fri Sep 14, 2012 10:24 am 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
Yeah its safe to ignore that warning :ugeek:

Code:
 # grep KALLSYMS /usr/src/linux/.config
CONFIG_KALLSYMS=y

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Top
   
PostPosted: Wed Sep 19, 2012 4:35 am 
Offline
Newbie

Joined: Thu Dec 06, 2007 9:58 am
Posts: 22
I have a question about Riser in kernel.
What is it?

I can't find any clues in http://kernel.org/doc/menuconfig/powerpc.html


Top
   
PostPosted: Wed Sep 19, 2012 7:00 am 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
Reiserfs support is enabled in the kernel for this build.
More info on Riser here: http://en.wikipedia.org/wiki/ReiserFS

However... I would go with something else... since Reiser is in the slammer for killing his wife... as you would expect support for the project is falling apart. http://arstechnica.com/uncategorized/2008/07/reiserfs-fading-into-obscurity-as-maker-leads-cops-to-corpse/

On a nicer note ext4 would be a good general purpose choice.

Stonie.

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Last edited by stonie on Wed Sep 19, 2012 8:34 am, edited 2 times in total.

Top
   
PostPosted: Wed Sep 19, 2012 7:51 am 
Offline
Newbie

Joined: Thu Dec 06, 2007 9:58 am
Posts: 22
I see. Thanks a lot. :)

So Riser = Reiserfs in kernel
In the first post, It seems lack one word "e" in Reiser.


Top
   
PostPosted: Wed Sep 19, 2012 8:31 am 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
Oops yeah... spello. :shock: :?

Sorry for the confusion... I have updated the spelling in the OP - Thanks.

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Top
   
PostPosted: Fri Jan 04, 2013 2:58 pm 
Offline
Newbie

Joined: Thu Dec 06, 2007 9:58 am
Posts: 22
I got a new problem when connect ls to the giga switch...

In syslog
--
Jan 4 10:17:13 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:17:13 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:17:13 LS-HG kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 4 10:17:13 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:17:13 LS-HG kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jan 4 10:17:51 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:17:55 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:18:00 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:18:03 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:29:59 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:30:04 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:30:09 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:30:12 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:35:30 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:35:32 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:45:54 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:45:59 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 10:46:04 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 10:46:07 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:25:08 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:25:10 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:25:20 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:25:22 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:25:23 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:25:25 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:25:26 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:25:29 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:25:30 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:25:32 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:27:14 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:27:16 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:32:34 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
Jan 4 17:32:36 LS-HG kernel: r8169 0000:00:0b.0: eth0: link up
Jan 4 17:32:42 LS-HG kernel: r8169 0000:00:0b.0: eth0: link down
--

Then the eth0 really link down until I restart the LS-HG.

After google I found one solution (autoneg off) but it's only use on 100M environment.
Any idea?


Top
   
PostPosted: Sat Jan 05, 2013 12:01 am 
Offline
Regular Member
User avatar

Joined: Mon Oct 08, 2007 6:34 am
Posts: 334
Have you tried another switch / cable ?

_________________
KuroHG - UBoot 1.2, foonas-em & Debian Wheezy - 3.4 Kernel
Kurobox Pro - Dave's Lenny-armel
LS-WVL - opened
LS-XHL - Squeeze Bootstrap
LS-VL - Squeeze Bootstrap


Top
   
PostPosted: Mon Jan 07, 2013 5:55 pm 
Offline
Newbie

Joined: Thu Dec 06, 2007 9:58 am
Posts: 22
stonie wrote:
Have you tried another switch / cable ?


I'll take a try. Thanks stonie.


Top
   
PostPosted: Thu Jan 10, 2013 5:35 pm 
Offline
Total Newbie

Joined: Wed Jan 09, 2013 2:49 am
Posts: 3
Worked like a charm. Thanks Stonie!


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 38 posts ]  Go to page Previous 1 2 3 Next

All times are UTC+01:00


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Powered by phpBB® Forum Software © phpBB Limited