Buffalo NAS-Central Forums

Welcome to the Linkstation Wiki community
It is currently Fri Nov 24, 2017 5:39 pm

All times are UTC+01:00




Post new topic  Reply to topic  [ 40 posts ]  Go to page Previous 1 2 3 Next
Author Message
PostPosted: Sat Feb 04, 2017 3:08 pm 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
0,1s


Top
   
PostPosted: Sat Feb 04, 2017 4:06 pm 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Hello

I have done the modification to the hddrootfs.img file on Knoppix meanwhile following this procedure http://buffalo.nas-central.org/wiki/Category:LS-WXL

I haven't installed it yet tho

However I think I have found a small error on the procedure, on step 3, when modifying /etc/sshd_config:
Code:
 sed -i 's/PermitRootLogin/# PermitRootLogin/' sshd_config


the default file is like this:
Code:
#PermitRootLogin yes
PermitRootLogin no


If you run the line mentioned above, the output of the file will add another # to the preceding # on the first PermitRootLogin line:
Code:
##PermitRootLogin yes
PermitRootLogin no


And I think what the wiki means is to uncomment the line (I don't know why the line is duplicated in the original file tho)

So what I would do is this:
Code:
#PermitRootLogin yes
PermitRootLogin yes


or supress the bottom PermitRootLogin line, uncomment the first line and leave it like this:
Code:
PermitRootLogin yes


However I think my device has a hardware problem, the network interface won't always come on and I just tried to transfer data to it again after being completely clean and the network interface got down, then it went back again and the transfer was incomplete.


Top
   
PostPosted: Sat Feb 04, 2017 6:34 pm 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
what you are doing

if you need ssh

this is possible with 2 clicks

http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/ssh-freischalten-mit-2-klicks-t2468.html

and this is the old way i have pretested
sed -i 's/PermitRootLogin no/PermitRootLogin yes/g' /etc/sshd_config

from
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/fw-1-56-offen-ssh-auf-eine-ls-chlv2-fw-1-56-t1220.html


Top
   
PostPosted: Sat Feb 04, 2017 7:18 pm 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Oh

I did the procedure from the wiki on this site. I can try the other way then, the wiki is outdated then

However my device acts weird, if I disconnect it from the network by unplugigng the cable and connect it back, it won't turn the network light on anymore until a long time.

When starting up the NAS it takes around 3 minutes too boot up apparently, but the network might not even come on until a long time later

I also have tried to change its IP, and when I did so, the network light went off.


Top
   
PostPosted: Sat Feb 04, 2017 8:10 pm 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Checked dmesg

Code:
Booting Linux on physical CPU 0
Initializing cgroup subsys cpu
Linux version 3.3.4-88f6281 (root@HP7907) (gcc version 4.2.0 20070413 (prerelease)) #7 Fri Mar 27 10:50:54 JST 2015
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
paging_init: zero_page=0xc7ffc000
arm_bootmem_init: boot_pages=0x1 bitmap=0x7ffb000
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c051ec1c, node_mem_map c1401000
  Normal zone: 256 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 32512 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,12M panic=5 BOOTVER=0.21 mtdparts=nand_mtd:0x1000000(boot),0xfe800000(rootfs),0x800000(reserve)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 105124k/105124k available, 25948k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc04ce000   (4888 kB)
      .init : 0xc04ce000 - 0xc04f3000   ( 148 kB)
      .data : 0xc04f4000 - 0xc0520620   ( 178 kB)
       .bss : 0xc0520620 - 0xc0532428   (  72 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x17568 - 0x175a4
€ : consistent_pte=0xc4000b80
xor: measuring software checksum speed
   arm4regs  :   544.400 MB/sec
   8regs     :   413.200 MB/sec
   32regs    :   463.200 MB/sec
xor: using function: arm4regs (544.400 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size  64MB
SDRAM_CS1 ....base 04000000, size  64MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PEX1_MEM ....no such
PEX1_IO ....no such
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch13)-- MVWXL  Soc: 88F6281 A1 LE

 Detected Tclk 166666667 and SysClk 300000000
gpiochip_add: registered GPIOs 0 to 63 on device: mv_gpio
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c4049000
PEX0 interface detected no Link.
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x0000-0xffffffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
PCI: bus0: Fast back to back transfers enabled
mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
bio: create slab <bio-0> at 0
raid6: int32x1     60 MB/s
raid6: int32x2     70 MB/s
raid6: int32x4     67 MB/s
raid6: int32x8     59 MB/s
raid6: using algorithm int32x2 (70 MB/s)
vgaarb: loaded
SCSI subsystem initialized
Switching to clocksource kw_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12288K
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c04d6134)
MV Buttons Driver Load
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
initial_polarity_val = 0x00000000
initial_polarity_val_high = 0x00038e50
Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 229
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
brd: module loaded
loop: module loaded
Integrated Sata device found
mvSataInitAdapter : regVal changed(0x00000010)
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
** BUFFALO Disable Command Queuing Function [0 1] **
scsi 0:0:0:0: Direct-Access              WD5000AAKS-00V1A 05.0 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access              WD5000AAKS-00V1A 05.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 1:0:0:0: [sdb] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
SPI Serial flash detected @ 0xf4000000, 512KB (8sec x 64KB)
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 23 00 00 00
NAND device: Manufacturer ID: 0xc1, Chip ID: 0xc1 (Unknown NAND 128MiB 3,3V 16-bit)
NAND bus width 8 instead 16 bit
No NAND device found
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 2 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o Gateway support enabled
     o Using Marvell Header Mode
     o L2 IGMP support
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
     o register under mv88fx_eth platform
     o eth0, ifindex = 2, GbE port = 0
     o eth1, ifindex = 3, GbE port = 1

rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Registering the dns_resolver key type
rtc-mv rtc-mv: setting system clock to 2017-02-05 03:56:14 UTC (1486266974)
 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] Attached SCSI disk
 sda: sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 800c0910 to a partition!
mdadm: sending ioctl 800c0910 to a partition!
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
bio: create slab <bio-1> at 1
md/raid1:md0: active with 2 out of 2 mirrors
md0: detected capacity change from 0 to 1024393216
 md0: unknown partition table
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md0): using internal journal
EXT3-fs (md0): mounted filesystem with writeback data mode
md: md10 stopped.
md: bind<sdb5>
md: bind<sda5>
md/raid1:md10: active with 2 out of 2 mirrors
md10: detected capacity change from 0 to 1024446464
md: md1 stopped.
md: bind<sdb2>
md: bind<sda2>
md/raid1:md1: active with 2 out of 2 mirrors
md1: detected capacity change from 0 to 5119135744
 md1: unknown partition table
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md1): using internal journal
EXT3-fs (md1): recovery complete
EXT3-fs (md1): mounted filesystem with writeback data mode
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md1): using internal journal
EXT3-fs (md1): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 9:1.
Trying to move old root to /initrd ... okay
Freeing init memory: 148K
udevd (818): /proc/818/oom_adj is deprecated, please use /proc/818/oom_score_adj instead.
 md10: unknown partition table
Adding 1000432k swap on /dev/md10.  Priority:-1 extents:1 across:1000432k
kjournald starting.  Commit interval 5 seconds
EXT3-fs (md0): using internal journal
EXT3-fs (md0): mounted filesystem with writeback data mode
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
eth1: started
scsi_verify_blk_ioctl: 302 callbacks suppressed
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
md: md21 stopped.
md: bind<sda6>
md/raid1:md21: active with 1 out of 2 mirrors
md21: detected capacity change from 0 to 484830812160
 md21: unknown partition table
md: md22 stopped.
md: bind<sdb6>
md/raid1:md22: active with 1 out of 2 mirrors
md22: detected capacity change from 0 to 484830812160
 md22: unknown partition table
scsi_verify_blk_ioctl: 470 callbacks suppressed
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
mdadm: sending ioctl 1261 to a partition!
XFS (md21): Mounting Filesystem
XFS (md21): Ending clean mount
XFS (md22): Mounting Filesystem
XFS (md22): Ending clean mount
bfSetMagicKey > Changed to 0x71 from 0x5c
eth1: link up, full duplex, speed 10 Mbps


I really wonder how the eth1 link is getting 10Mbps!!!!
The device is getting 1,12 MB/s now

I am transferring stuff to it so it will eventually "leave" the network, once it gets back I will try to check the dmesg log again.

Short version:
Code:
Loading Marvell Ethernet Driver:
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
     o register under mv88fx_eth platform
     o eth0, ifindex = 2, GbE port = 0
     o eth1, ifindex = 3, GbE port = 1
eth1: started
eth1: link up, full duplex, speed 10 Mbps


Top
   
PostPosted: Sat Feb 04, 2017 9:30 pm 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
eth1: link up, full duplex, speed 10 Mbps

you have checked a other cable and port
then your nas is demaged
replace it with the fastest Kirkwood LS-WVL (1600Mhz vs 600Mhz)


Top
   
PostPosted: Sat Feb 04, 2017 10:32 pm 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Yes

I think it's damaged too. I tried several different cables and several different ports in my router

Also I restarted and got this:
Code:
eth1: link up, full duplex, speed 1 Gbps
eth1: link down
eth1: link up, full duplex, speed 1 Gbps
eth1: link down
eth1: link up, full duplex, speed 10 Mbps


It apparently seems to be some kind of hardware failure.

I will try to send it to Buffalo for repair first as I wouldn't need to get a newer model if this one worked fine.
Btw, is there any dissasembly guide?
If the ethernet port is damaged, I might be able to solder a new one

Thanks


Top
   
PostPosted: Sat Feb 04, 2017 10:46 pm 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Code:
bad rx status 2f8036d9, (crc error)
eth1: link down
eth1: link up, full duplex, speed 1 Gbps
eth1: link down
eth1: link up, full duplex, speed 1 Gbps
eth1: link down
eth1: link up, full duplex, speed 1 Gbps
eth1: link down
eth1: link up, full duplex, speed 1 Gbps
eth1: link down
eth1: link up, full duplex, speed 100 Mbps
eth1: link down
eth1: link up, full duplex, speed 100 Mbps
eth1: link down
eth1: link up, full duplex, speed 100 Mbps
eth1: link down
eth1: link up, full duplex, speed 100 Mbps
eth1: link down
eth1: link up, full duplex, speed 100 Mbps
eth1: link down
eth1: link up, full duplex, speed 10 Mbps
bad rx status 6f834859, (crc error)
bad rx status 6f83f401, (crc error)
bad rx status 6f861b09, (crc error)


This is what happened after a few devices on my network attempted to do a file transfer to the NAS so there's definetly some kind of failure in the NAS


Top
   
PostPosted: Sat Feb 04, 2017 10:51 pm 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
Quote:
If the ethernet port is damaged, I might be able to solder a new one


Don not do that.
your old nas you can get on ebay for 30€

You are in varanty with this old mashine?


Top
   
PostPosted: Sat Feb 04, 2017 10:55 pm 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Really?
I think I paid 60 euros for this one in eBay :))

No, I don't think it's in warranty, but I haven't found any cheap one in eBay except on bids, and they raise up pretty quick..
So I gues it might be a good tryto dissasemble it if the repair is easy..


Top
   
PostPosted: Sun Feb 05, 2017 1:00 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
in germany it is cheaper.

you can check
- the soldering quality
- the wires in the rj45 jack


the chips should be ok


Top
   
PostPosted: Sun Feb 05, 2017 1:41 am 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
I am from Spain, I ordered it from a German guy in 2015 tho

Is there any dissasembly guide? I don't seem to find how to open it.

Thanks


Top
   
PostPosted: Sun Feb 05, 2017 1:47 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
I make a guide now


Top
   
PostPosted: Sun Feb 05, 2017 1:49 am 
Offline
Newbie

Joined: Fri Feb 03, 2017 11:56 am
Posts: 28
Really?

I am embarrased then :)) As I can't find how to open it, I just know how to take the disks out :))
I ust see 2 screws behind, but I can't find how to continue from there. I actually have dissasembled more complex things than this, but I am unable to find what to do next


Top
   
PostPosted: Sun Feb 05, 2017 2:29 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2691
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/oeffnen-einer-ls-wvl-ls-wxl-t2657.html


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 40 posts ]  Go to page Previous 1 2 3 Next

All times are UTC+01:00


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Powered by phpBB® Forum Software © phpBB Limited