Buffalo NAS-Central Forums

Welcome to the Linkstation Wiki community
It is currently Sat Oct 21, 2017 4:36 pm

All times are UTC+01:00




Post new topic  Reply to topic  [ 17 posts ]  Go to page 1 2 Next
Author Message
 Post subject: LS-CHL-V2 no boot lights
PostPosted: Sat May 28, 2011 7:42 pm 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
switched my nas on today no boot I hear fan and hard drive running but no blue or any other color lights at front only power and network cable green light at rear,
I flashed firmware 1.37 yeterday then turned off nas and went to bed, what next for me please. :(


Top
   
PostPosted: Sun May 29, 2011 12:46 pm 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2689
http://buffalo.nas-central.org/index.php/Revive_your_arm9_box_from_scratch

use this tftp
http://download.discountnetz.com/tftp-boot-recovery/TFTP_Boot_Recovery_1.24_All_4_Models.zip


Top
   
PostPosted: Mon May 30, 2011 7:38 am 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
oxygen8 wrote:


Have tried this but there is no attempt to boot at all no lights at front of box.

No EM mode.

Can these boxes be jtag 'ed


Last edited by brianw on Mon May 30, 2011 7:54 am, edited 1 time in total.

Top
   
PostPosted: Mon May 30, 2011 7:53 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2689
If you are in waranty, use it.

Remove Harddrive.
Connect it to PC.
Delete all Partitions.
Connect HDD to LS.
power on
You should get E06 (red blinking)

Use TFTP-
Set
NoFormatting = 0
in lsupdater.ini
Aktivate Debug.
Use rebuild partition table.
Flash firmware.


Top
   
PostPosted: Mon May 30, 2011 7:57 am 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
oxygen8 wrote:
If you are in waranty, use it.

Remove Harddrive.
Connect it to PC.
Delete all Partitions.
Connect HDD to LS.
power on
You should get E06 (red blinking)

Use TFTP-
Set
NoFormatting = 0
in lsupdater.ini
Aktivate Debug.
Use rebuild partition table.
Flash firmware.


Thanks for replying m8, but I don't get any blinking lights at all.

can these boxes be jtag'ed


Top
   
PostPosted: Mon May 30, 2011 8:00 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2689
In 5 min
Quote:
Remove Harddrive.
Connect it to PC.
Delete all Partitions.
Connect HDD to LS.
power on
You should get E06 (red blinking)


You are very quick.

You do not need JTAG if you do not write to flash (bootloader).
Never set Update Boot under LSUpdater Debug.


Last edited by oxygen8 on Mon May 30, 2011 8:03 am, edited 1 time in total.

Top
   
PostPosted: Mon May 30, 2011 8:02 am 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
oxygen8 wrote:
In 5 min
Quote:
Remove Harddrive.
Connect it to PC.
Delete all Partitions.
Connect HDD to LS.
power on
You should get E06 (red blinking)


You are very quick.


Yes I had already deleted partitions in desperation. :(


Top
   
PostPosted: Mon May 30, 2011 8:09 am 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
oxygen8 wrote:
You do not need JTAG if you do not write to flash (bootloader).
Never set Update Boot under LSUpdater Debug.


I think maybe I did this before it went dead on me cuz these are default in Debug yes.


Top
   
PostPosted: Mon May 30, 2011 8:26 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2689
FW 1.37 mod1 from Shonk use Update Boot.
When you have a power cut while update boot, you need a jtag.


Top
   
PostPosted: Mon May 30, 2011 8:32 am 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
oxygen8 wrote:
FW 1.37 mod1 from Shonk use Update Boot.
When you have a power cut while update boot, you need a jtag.


I think I need to JTAG is this possible with LS-CHL V2. :)


Top
   
PostPosted: Mon May 30, 2011 9:00 am 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2689
I never read about.
LS-XHL is the same?

http://buffalo.nas-central.org/wiki/Serial_and_JTAG_port_LS-XHL


Top
   
PostPosted: Thu Jun 02, 2011 11:13 am 
Offline
Newbie

Joined: Fri Nov 12, 2010 7:22 am
Posts: 21
oxygen8 wrote:


thanks for info just getting the hardware together. :)


Top
   
PostPosted: Wed Jun 26, 2013 10:46 pm 
Offline
Total Newbie

Joined: Wed Jun 26, 2013 10:41 pm
Posts: 1
brianw wrote:
Thanks for replying m8, but I don't get any blinking flashlight at all.
can these boxes be jtag'ed

I think you should go with oxygen8 advice.
Though he was very quick but I probably use his tricks if I were in place of you.


Top
   
PostPosted: Sun Jan 08, 2017 6:44 pm 
Offline
Newbie

Joined: Sun Mar 08, 2015 12:58 pm
Posts: 24
hello,

my LS-CHL too can not boot. no light showing at all when i turn the switch ON. i dont feel the drive is starting.

anyone can help ? i already dissamble the NAS and delete all the partition but still no response from the NAS.


Top
   
PostPosted: Sun Jan 08, 2017 7:09 pm 
Offline
Moderator

Joined: Mon Apr 26, 2010 10:24 am
Posts: 2689
check your powersupply


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 17 posts ]  Go to page 1 2 Next

All times are UTC+01:00


Who is online

Users browsing this forum: No registered users and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Powered by phpBB® Forum Software © phpBB Limited