Firmware for LS-LGL series

gvd · **Posted:** Wed Jul 25, 2007 10:13 am

There is a new LS-LGL series available in Japan. http://buffalo.jp/products/catalog/storage/ls-lgl/index.html

It is a smaller then the other Gigabit Linkstation and costs only little more then the old HD-HLAN series.

Does anyone know if it can install FreeLink or OpenLink?

lb_worm · **Posted:** Wed Jul 25, 2007 12:23 pm

I saw this when I was out this last. Do not know anymore about the box. If we can get some specs on this then it may already be supported.

gvd · **Posted:** Thu Jul 26, 2007 5:01 am

I was curious and got one. It is quickly opened. Inside is a marvell processor. I can try to figure out more if someone tells me what to look for...

gvd · **Posted:** Thu Jul 26, 2007 5:39 am

The firmware on the LS-LGL is completely stripped down. It does not run a web server. It is configured through the nas navigator utility only. I should have checked the manual before getting it...

mindbender · **Posted:** Thu Jul 26, 2007 9:23 am

hmm...well..this is what i would do:

1) open it again and post pictures!

2) try acp_commander to get telnet/root access!

with luck it is only a stripped down version but similar mainboard..who knows..

gvd · **Posted:** Thu Jul 26, 2007 2:37 pm

I already took some pictures. But actually there is really little to see as the main board is quite small compared to the LS Pro. So here is a photo:

I have opened the linkstation and removed the hard drive which covered part of the main board. The front of the drive is at the right, the bottom at the bottom. The drive is plugged directly into the socket on the main board. I think flickr reduced the resolution of the picture a little and I cannot attach the full resolution image to this forum. It is hard to read what is printed on the processor. The top line says "88FB-LKJ1".

I have tried acp_command and got telnet access to the box. I also tried to connect the hard drive to my computer and was able to mount and access the partitions.

Any other information or close ups of the box?

mindbender · **Posted:** Thu Jul 26, 2007 2:56 pm

1) i don`t know if you want to do that...but could you maybe completely disassemble the box and take high detailed pictures of the mainboard?

2) give us some infos like i did here:
viewtopic.php?f=22&t=3046

as far as i know this box does not have any usb-ports....so most likely there is no support for usb-stuff.

unfortunately i don`t see the LS-LGL here at the japanese firmware downloadpage:
http://buffalo.jp/download/driver/index_seihin_l.html

if we had a firmware for the box we could look at the firmware directly....but maybe it is just not available...who knows. i recommend to look at the japanese page regularily and check if they added the LS-LGL there....i at least know that they call it the same because
http://buffalo.jp/products/catalog/storage/ls-lgl/

the moment there is a firmware update there we can look in getting a different image on the box....

gvd · **Posted:** Thu Jul 26, 2007 3:16 pm

I'll see if I can disassemble the rest of the box to get a full picture of the mainboard. The way it is assembled it looks more tricky then the part so far. As 90% of the mainboard is already visible I may also try to get some close ups in the box. The other board at the top on the other side is only power as far as I can tell.

The LS-LGL does not have USB ports.

There is no firmware available, yet. The box runs version 1.0. However, I am not sure if we will see very many firmware versions if any for the LS-LGL. You can only configure it through the NAS Navigator. It only has a single share. It can only be protected with a single password. It would be pretty hard to get some bugs into there which would require a firmware upgrade and I kind of doubt that they will add any more additional features the way it is configured at the moment. But we'll see.

I'll try to take some more photos and make the shell output at the weekend...

mindbender · **Posted:** Thu Jul 26, 2007 3:25 pm

but at least we could ask them for the GPL sourcecode.

i mean...it obviously is running linux with many GPL stuff in it.....

then we see the kernel and we can compare it with the LS-GL/LS Live one.

additionally to the infos in the link described above please post some information about the directory layout...

ls /
ls /boot
ls /mnt
ls /etc
and so on....
...who knows, maybe it is possible to install FreeLink/GenLink via modifying the hdd on a pc.

Kaiten · **Posted:** Thu Jul 26, 2007 3:34 pm

mindbender wrote:

but at least we could ask them for the GPL sourcecode.

While you're at it, could you speak nicely to your contacts & see if you can obtain the source for nas_configgen

Georg · **Posted:** Thu Jul 26, 2007 8:04 pm

Kaiten wrote:

While you're at it, could you speak nicely to your contacts & see if you can obtain the source for nas_configgen

... and the ACP-Commands, especially the authentication process. :lol:

mindbender · **Posted:** Fri Jul 27, 2007 12:19 pm

this is no wishlist guys

i don`t think they will ever give us the source as nas_configgen and the ls_servd(acp_commands) are the 2 special things from the linkstation....things that make the boxes different to other manufacturers....

back to topic please

gvd · **Posted:** Fri Jul 27, 2007 1:47 pm

O.K. Here the output from the shell...

Code:

Trying 192.168.2.92...
Connected to 192.168.2.92.
Escape character is '^]'.


BUFFALO INC. LinkStation series LS-LGL(SUIZEI)

LS-LGL27A login: root


BusyBox v1.1.1 (2007.05.08-14:05+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ # cd ..
/ # ls
bin         etc         lib         proc        sbin        usr
boot        home        lost+found  root        sys         var
dev         initrd      mnt         rootfs      tmp
/ # mount
rootfs on / type rootfs (rw)
/dev/root on / type ext3 (rw)
proc on /proc type proc (rw,nodiratime)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
/dev/disk1_1 on /boot type ext3 (rw)
/dev/disk1_6 on /mnt/disk1 type xfs (rw)
/ # uname -r
2.6.12.6-arm1
/ # cat /proc/cmdline
console=ttyS0,115200 root=/dev/sda2 rw initrd=0x01400000,4M panic=5 BOOTVER=1.02L
/ # cat /proc/cpuinfo
Processor       : ARM926EJ-Sid(wb) rev 0 (v5l)
BogoMIPS        : 219.54
Features        : swp half thumb fastmult 
CPU implementer : 0x41
CPU architecture: 5TEJ
CPU variant     : 0x0
CPU part        : 0x926
CPU revision    : 0
Cache type      : write-back
Cache clean     : cp15 c7 ops
Cache lockdown  : format C
Cache format    : Harvard
I size          : 16384
I assoc         : 1
I line length   : 32
I sets          : 512
D size          : 16384
D assoc         : 1
D line length   : 32
D sets          : 512

Hardware        : Feroceon
Revision        : 0000
Serial          : 0000000000000000
/ # cat /proc/meminfo
MemTotal:        13632 kB
MemFree:          1040 kB
Buffers:          1352 kB
Cached:           5324 kB
SwapCached:          0 kB
Active:           6616 kB
Inactive:         2900 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        13632 kB
LowFree:          1040 kB
SwapTotal:      136512 kB
SwapFree:       136512 kB
Dirty:              48 kB
Writeback:           0 kB
Mapped:           5928 kB
Slab:             1880 kB
CommitLimit:    143328 kB
Committed_AS:    17332 kB
PageTables:        288 kB
VmallocTotal:   491520 kB
VmallocUsed:       464 kB
VmallocChunk:   491056 kB
/ # cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00001000 "marvell_flash"
/ # cd /proc
/proc # lspci
-sh: lspci: not found
/proc # cat partitions
major minor  #blocks  name

   8     0  244198584 sda
   8     1     200781 sda1
   8     2     498015 sda2
   8     4          1 sda4
   8     5     136521 sda5
   8     6  243360621 sda6
  31     0        256 mtdblock0
/proc # ls
1            3            647          cmdline      kmsg         slabinfo
1002         32           654          cpu          loadavg      stat
1040         33           708          cpuinfo      locks        swaps
1050         338          751          devices      meminfo      sys
1059         34           886          diskstats    misc         sysvipc
1088         35           9            driver       modules      tty
1092         37           910          execdomains  mounts       uptime
1122         38           975          filesystems  mtd          version
1148         39           979          fs           net          vmstat
1149         4            980          interrupts   partitions
162          5            buddyinfo    iomem        pci
175          633          buffalo      ioports      scsi
2            637          bus          kallsyms     self
/proc # cd buffalo
/proc/buffalo # ls
PowerSWInt_en  cpu_status     fan_status     hdd_control    led
cpu_reset      enet           firmware       kernevnt       power_sw
/proc/buffalo # cat enet
MAC=00:16:01:D7:42:7B
link=1000Mbps
duplex=full
jumboframe=enable
mtu=1500
/proc/buffalo # cat firmware
PRODUCTNAME=LS-LGL(SUIZEI)
VERSION=0.01
SUBVERSION=FLASH 0.00
PRODUCTID=0x0000000B
BUILDDATE=2007/06/11 15:39:50
BOOTVER=1.02L
/proc/buffalo # cat kernevnt
^C
/proc/buffalo # cat lcd
cat: lcd: No such file or directory
/proc/buffalo # cat led
cat: Read Error: Is a directory
/proc/buffalo # cat cpu_status
normal_state
/proc/buffalo # cat hdd_control
on
/proc/buffalo # cd ..
/proc # cat buddyinfo
Node 0, zone      DMA      0     12      8      4      0      0      0      1      0      0      0 
/proc # cd /etc
/etc # ls
cron                 issue.net            passwd
daemonwatch.list     ld.so.cache          printcap
default              ld.so.conf           profile
dhcpc                linkstation_release  resolv.conf
fstab                localtime            resolv.conf.sv
group                logrotate.d          rootfs_ok
gshadow              melco                samba
hddrootmode          mtab                 services
hosts                mtab~                shadow
inetd.conf           nsswitch.conf        shadow-
init.d               ntp.conf             skel
initrd_ver           ntp.conf.sv          syslog.conf
inittab              pam.d                yp.conf
issue                pam_smb.conf         yp.conf.sv
/etc # cat inittab
::sysinit:/etc/init.d/rcS
::respawn:/sbin/getty -L ttyS0 115200 vt100

::restart:/sbin/init
::shutdown:/etc/init.d/rcDown
::shutdown:/bin/umount -r /
/etc # cd /bin
/bin # file bash
bash: ELF 32-bit LSB executable, ARM, version 1 (SYSV), for GNU/Linux 2.4.17, dynamically linked (uses shared libs), stripped
/bin # file busybox
busybox: ELF 32-bit LSB executable, ARM, version 1 (SYSV), for GNU/Linux 2.4.17, dynamically linked (uses shared libs), stripped
/bin # busybox
BusyBox v1.1.1 (2007.05.08-14:05+0000) multi-call binary

Usage: busybox [function] [arguments]...
   or: [function] [arguments]...

        BusyBox is a multi-call binary that combines many common Unix
        utilities into a single executable.  Most people will create a
        link to busybox for each function they wish to use and BusyBox
        will act like whatever it was invoked as!

Currently defined functions:
        [, [[, addgroup, adduser, ash, awk, basename, bunzip2, busybox,
        bzcat, cat, chgrp, chmod, chown, chroot, chvt, clear, cmp, cp,
        crond, crontab, cut, date, dd, deallocvt, delgroup, deluser, df,
        dirname, dmesg, du, echo, egrep, env, expr, false, fdflush, fgrep,
        free, freeramdisk, getopt, getty, grep, gunzip, gzip, halt, hdparm,
        head, hexdump, hostid, hostname, hwclock, id, ifconfig, inetd,
        init, install, kill, killall, length, linuxrc, ln, logger, login,
        logname, ls, md5sum, mkdir, mkfifo, mknod, mkswap, mktemp, more,
        mv, nice, od, openvt, passwd, pidof, ping, poweroff, printf, ps,
        pwd, readlink, realpath, reboot, renice, reset, rm, rmdir, route,
        run-parts, sed, seq, sh, sleep, sort, strings, stty, sum, swapoff,
        swapon, sync, sysctl, tail, tar, tee, telnetd, test, time, top,
        touch, tr, true, tty, uname, uniq, unzip, uptime, usleep, vi,
        watch, wc, which, who, whoami, yes, zcat

/bin # ls
addgroup   chown      egrep      kill       mv         sed        uname
adduser    cp         false      ln         nice       sh         unzip
ash        date       fdflush    login      pidof      sleep      usleep
bash       dd         fgrep      ls         ping       stty       vi
bash2      delgroup   getopt     mkdir      ps         sync       watch
busybox    deluser    grep       mknod      pwd        tar        zcat
cat        df         gunzip     mktemp     rm         touch
chgrp      dmesg      gzip       more       rmdir      true
chmod      echo       hostname   mount      run-parts  umount
/bin # dmesg
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #477 Mon Jun 11 15:39:52 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 1, 32 byte lines, 512 sets
CPU0: D cache: 16384 bytes, associativity 1, 32 byte lines, 512 sets
Machine: Feroceon
Using UBoot passing parameters structure
Sys Clk = 166666667, Tclk = 133333333
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 4096
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x01400000,4M panic=5 BOOTVER=1.02L
PID hash table entries: 128 (order: 7, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 8MB 8MB 0MB 0MB = 16MB total
Memory: 9416KB available (2186K code, 361K data, 96K init)
Calibrating delay loop... 219.54 BogoMIPS (lpj=1097728)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4096K
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size  16MB 
SDRAM_CS1 ....base 01000000, size  16MB 
PEX0_MEM ....base e0000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
NFLASH_CS ....base f9000000, size   2MB 
MFLASH_CS ....base f8100000, size 256KB 
SPI_CS ....base fa000000, size   8MB 
BOOT_ROM_CS ....base fc000000, size   1MB 
DEV_BOOTCS ....base fc000000, size   1MB 
CRYPT_ENG ....base f0000000, size  64KB 
 mv_mtd_initialize Error : Unknown board 

  Marvell Development Board (LSP Version 2.1.10_TG)-- RD-88F6082-DAS-PLUS  Soc: MV88F6082 Rev 1

 Detected Tclk 133333333 and SysClk 166666667 
Marvell USB EHCI Gadget controller #0: c02efb00
mvPexBarSet: ERR. Target 2 window invalid
mvPexInit: ERR. mvPexBarSet 2 failed
pci_init:Error calling mvPciIfInit for pciIf 0
IO Request resource failed - Pci If 0
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 3 RAM disks of 5120K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Marvell ethtool proc enabled
  o Rx desc: 64
  o Tx desc: 128
  o Loading network interface 'eth0' 'eth1' 
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
  Vendor: SAMSUNG   Model: SP2504C           Rev: VT10
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
physmap flash device: 40000 at f8100000
CFI: Found no phys_mapped_flash device at location zero
JEDEC: Found no phys_mapped_flash device at location zero
Marvell Flash Detected @ 0xf8100000, 256KB Main region (64sec x 4KB), 2KB Information region
mice: PS/2 mouse device common for all mice
mvGppValueSet: Err. An attempt to set output value to GPP 3 in input mode.
Buffalo Platform Linux Driver(Light) (C) BUFFALO INC. Ver.0.01 installed.
Kernel message queue controll (C) BUFFALO INC. Ver.1.00 installed.
Kernel event for procfs (C) BUFFALO INC. Ver.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 96K
Adding 136512k swap on /dev/disk1_5.  Priority:-1 extents:1
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
/bin # ls /sbin
depmod       fsck.ext2    ifconfig     mke2fs       poweroff     swapon
dhcpcd       fsck.ext3    init         mkfs.ext2    reboot       sysctl
e2fsck       getty        insmod       mkfs.ext3    rmmod        syslogd
fdisk        halt         klogd        mkswap       route        tune2fs
freeramdisk  hdparm       ldconfig     modinfo      shutdown
fsck         hwclock      lsmod        modprobe     swapoff
/bin # cat /proc/modules
/bin # cd /proc/bus/pci
/proc/bus/pci # cat devices
/proc/bus/pci # cd ..
/proc/bus # ls
input  pci
/proc/bus # cd /
/ # ls /
bin         etc         lib         proc        sbin        usr
boot        home        lost+found  root        sys         var
dev         initrd      mnt         rootfs      tmp
/ # ls /boot
conf_save.tgz       lost+found          u-boot.buffalo.org
initrd.buffalo      u-boot.buffalo      uImage.buffalo
/ # ls /mnt
authtest  disk1     nfs       ram       root      usbdisk1  usbdisk2
/ # ls /etc
cron                 issue.net            passwd
daemonwatch.list     ld.so.cache          printcap
default              ld.so.conf           profile
dhcpc                linkstation_release  resolv.conf
fstab                localtime            resolv.conf.sv
group                logrotate.d          rootfs_ok
gshadow              melco                samba
hddrootmode          mtab                 services
hosts                mtab~                shadow
inetd.conf           nsswitch.conf        shadow-
init.d               ntp.conf             skel
initrd_ver           ntp.conf.sv          syslog.conf
inittab              pam.d                yp.conf
issue                pam_smb.conf         yp.conf.sv
/ # ls /usr
bin    lib    local  sbin   share
/ # 
/ # ls /usr/bin
[             env           logger        sum           xfs_admin
[[            expr          logname       tail          xfs_bmap
awk           file          md5sum        tee           xfs_check
basename      find          mkfifo        test          xfs_copy
bunzip2       flex          nkf           time          xfs_db
bzcat         free          od            top           xfs_freeze
chvt          head          openvt        tr            xfs_growfs
cksum         hexdump       passwd        tty           xfs_info
clear         hostid        printf        uniq          xfs_io
cmp           id            readlink      unzip         xfs_logprint
crontab       install       realpath      uptime        xfs_mkfile
cut           killall       renice        uuidgen       xfs_ncheck
deallocvt     ldd           reset         wc            xfs_rtcp
diff          length        seq           which         yes
dirname       locale        sort          who
du            localedef     strings       whoami
/ # 
/ # ls /usr/sbin
chroot        gpasswd       inetd         mklost+found  useradd
crond         groupadd      logrotate     newgrp        userdel
dosfsck       groupdel      mkdosfs       newusers      usermod
fsck.xfs      groupmod      mkfs.xfs      telnetd       xfs_repair
/ # 
/ # ls /usr/local
bin   lib   sbin
/ # 
/ # ls /usr/local/bin
bootchange.sh        libbuffalo           smbcquotas
calib_time.sh        libbuffalo_bin       smbget
create_partition.sh  net                  smbpasswd
eventlogadm          nmblookup            smbspool
exec_libbuffalo      ntlm_auth            smbstatus
findsmb              pdbedit              smbtar
hdd_check_normal.sh  piconv               smbtree
hdd_format.sh        profiles             tdbbackup
iconv                restore_time.sh      tdbdump
imhere.sh            rpcclient            tdbtool
initsw.sh            set_timezone.sh      testparm
initweb.sh           shutdown.sh          uniconv
kernelmon_exec.sh    smbcacls             update_ntp.sh
keyinput             smbclient            vercomp
lcd_error_man.sh     smbcontrol           wbinfo
/ # 
/ # ls /usr/local/sbin
FanCheckd          logchkd            nmbd               setenv
clientUtil_server  miconapl           ntpdate            smbd
daemonwatch        mount.cifs         nvram              umount.cifs
kernelmon          nas_configgen      printenv           winbindd
/ # exit

mindbender · **Posted:** Fri Jul 27, 2007 2:23 pm

to be honest all this info looks damn similar to the ls pro/LS Live one.

i saw nothing there that makes me think that the firmware is different to the LS Pro/LS Live ones...it uses /boot for kernel/uImage, it boots to /dev/sda2, kernel seems to be built from the same kernel source, same kernel-uname......partitions sizes are the same....it features clientUtil_server which is the process used for updating the box via lsupdater, it even has the prepared mountpoints for the usbdisks....

the only thing missing are the usb-ports.

so...everything is prepared for firmware updates....

so....i give you a task for trying:
download jtymod and modify lsupdater.ini...change the product-id in it with
the on from

Code:

/proc/buffalo # cat firmware
PRODUCTNAME=LS-LGL(SUIZEI)
VERSION=0.01
SUBVERSION=FLASH 0.00
PRODUCTID=0x0000000B
BUILDDATE=2007/06/11 15:39:50
BOOTVER=1.02L

i think there are good chances that it will find the box. but don`t try to update it...just look if the updater finds the box.....if yes left click on the 2 yellow rings at the top and select debug...ah and besides: disable your firewall before doing anything. it won`t work with any firewall enabled because the packets sent to the box + replies are operating on a lower level than tcp/udp....there are broadcasts on the network layer (see OSI at wikipedia if you do not know this)

..and report back your findings!

gvd · **Posted:** Fri Jul 27, 2007 4:08 pm

It does not find the LS-LGL. The uploader still only finds the LS-GL in my network. It seems as if changing the product code does not make any difference.

What worries me a little bit is the limited amount of memory in the LS-LGL. I wonder if it is enough to get a usable server...

Buffalo NAS-Central Forums

Firmware for LS-LGL series

Who is online