Buffalo NAS-Central Forums

Welcome to the Linkstation Wiki community
It is currently Thu Jul 24, 2014 3:30 am

All times are UTC [ DST ]




Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4  Next
Author Message
 Post subject: Serial @ Pro Duo
PostPosted: Sun Feb 17, 2008 12:39 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
Have someone succesfully added an serial port to the pro duo? If yes, how? What I would need, do that?

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Sun Feb 17, 2008 1:22 pm 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
are there any internal pics available from the LS Pro DUO?

i would help in localizing serial.

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Sun Feb 17, 2008 1:46 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
No problem!

Here the pictures:
Image
Image

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Sun Feb 17, 2008 2:01 pm 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
the 4 holes on the right of picture 1 and left on picture 2 look like serial.

serial uses 4 pins:
Tx, Rx , GND, VCC

the pinout is just a little unclear.

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Sun Feb 17, 2008 2:07 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
Hmmmm ... okay ... i'm not really the hardware geek and do first trying by trial and error, getting a new kernel working ... if i've no success, maybe someone here in the corner (frankfurt) can help me.

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Mon Feb 18, 2008 11:32 am 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
ok some more info regarding what i see.

i don`t see anything that could possible be a jtag port for example. for me it seems as if the LS Pro DUO does not have obvious connectors for jtag....which is bad.

i have posted your pictures in the wiki...i hope this is no problem.

http://buffalo.nas-central.org/index.ph ... LS-WTGL/R1

regarding finding out the serial pinout:
1 of the 4 pins should have 3.3V ....you won`t have to connect this one! as long as you do not connect voltage with anything you cannot destroy anything. i have some usb2serial-cables which you could use for getting serial access on the LS Pro duo. if you are interested i can send one to you (you donate shipping). these cables have the PL-2303 chip inside. colors are the same as i described here
Image

additional info: http://buffalo.nas-central.org/index.ph ... inkstation
http://www.nslu2-linux.org/wiki/HowTo/AddASerialPort

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Tue Mar 18, 2008 6:17 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
@mindbender:

I got now your USB cable. I opened also the part of the cable which should be connected to the device. Now I see an red, green, white, black and blue cable. Next I'll soldering the pins on the duo board.
So far I understand it right, I can connect every cable to every pin without destroy the duo board, is that right?

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Tue Mar 18, 2008 7:04 pm 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
do not shorten GND and VCC! thats important! this can kill the box. goauld just experienced this i think lately.

i ll recheck the pinout with a voltmeter for you as i have an open cable. please wait till tomorrow for that. i want to finish my master thesis tonight.

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Tue Mar 18, 2008 7:19 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
Okay - so far I can soldering the pins to the duo board and prepare the single cables so that they are plugable. Then, when I know the correct pinout, I'll try to connect.

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Wed Mar 19, 2008 7:50 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
Okay - I think i doesn't win any price for that, but my duo board has now pins and the cable can pluged to that pins. Now I only need the pinout ;-)
Image
Full size

Image
Full size

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Wed Mar 19, 2008 8:46 pm 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
i ll check the pinout in a few minutes.

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Wed Mar 19, 2008 9:08 pm 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
ok. its as i said the same as the pic. only difference the grey cable from the picture is white on the one you have.

white = TxD
blue = RxD
black = GND

as long as you only deal with this three cables everything is ok and can`t damage your box.

its only dangerous when messing with Power aka VCC. but to be extra careful make sure you do not shorten anything...

Don`t get confused by the pinout used on the cable on the picture....it is a reversed pinout as it gets pressed on pads on the board. i would expect that you have to connect it on the board this way when you can read the string CN10 normally:

RxD - TxD - space, nothing - GND


Attachments:
usb-phone-sync-cable.JPG
usb-phone-sync-cable.JPG [ 87.48 KiB | Viewed 4962 times ]

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!
Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Thu Mar 20, 2008 9:18 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
YES - it works!

The pinout (if you look on the board from the backside): [GND]-[ ]-[TxD]-[RxD]

Here the output (I plugged only the power - the Duo isn't powered on):
Code:
> Checking hardware info ...
=== Strap status : 0x00002030 ===
=== H/W boardId  :       0x13 ===
=== boardId      :       0x18 ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-WTGL/R1 U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_WTGL/R1 LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Jan  7 2008 - 21:04:08) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.13-1.00

DRAM CS[0] base 0x00000000   size  64MB
DRAM Total size  64MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x3a
buffalo_IsStopAtUbootStatus > MagicKey=0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...

And this all happens during reaching runlevel 2 (i powered on the box):
Code:
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJDSP620337
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
  Device 1: OK
Model: SAMSUNG HD501LJ                          Firm: CR100-12 Ser#: S0Z4J1FP804864
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/initrd.buffalo

4563579 bytes read
Using device ide1, partition 1

Loading from block device ide device 1, partition 1: Name: hdb1
  Type: U-Boot  File:/initrd.buffalo

4563579 bytes read
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJDSP620337
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
  Device 1: OK
Model: SAMSUNG HD501LJ                          Firm: CR100-12 Ser#: S0Z4J1FP804864
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1949476 bytes read
Using device ide1, partition 1

Loading from block device ide device 1, partition 1: Name: hdb1
  Type: U-Boot  File:/initrd.buffalo

4563579 bytes read
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.16.16-teralive110gpl4L
   Created:      2007-11-03  22:18:47 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1949412 Bytes =  1.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
   Image Name:   initrd
   Created:      2006-12-27  21:19:31 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4563515 Bytes =  4.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

arg:console=ttyS0,115200 mem=64m root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux...........................................................................................
Linux version 2.6.16.16-teralive110gpl4LSPro-mb_v6 (mindbender@mindbender) (gcc version 3.4.4 (release) (Code7
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740


- Warning - This LSP release was tested only with U-Boot release 1.7.3

Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 mem=64m root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 45384KB available (3340K code, 596K data, 116K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL

 Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
Request resource failed - PEX 0
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011b74)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
** BUFFALO Disable Command Queuing Function [0 1] **
  Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
  Type:   Direct-Access                      ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c37bbba0
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c37bbba0
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
sd 1:0:0:0: Attached scsi disk sdb
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
physmap flash device: 400000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Platform Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16-teralive110gpl4LSPro-mb_v6 ehci_hcd
usb usb1: SerialNumber: ehci_platform.4523
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: Product: EHCI Platform Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16-teralive110gpl4LSPro-mb_v6 ehci_hcd
usb usb2: SerialNumber: ehci_platform.16781
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.3
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   308.800 MB/sec
   8regs     :   217.600 MB/sec
   32regs    :   252.400 MB/sec
raid5: using function: arm4regs (308.800 MB/sec)
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb6 ...
md:  adding sdb6 ...
md:  adding sda6 ...
md: created md2
md: bind<sda6>
md: bind<sdb6>
md: running: <sdb6><sda6>
raid1: raid set md2 active with 2 out of 2 mirrors
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
---- in Modified linuxrc ---
Thu Mar 20 20:17:05 JST 2008
err: RecvPacket: readlen=0.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
err: RecvPacket: readlen=0.
err: RecvPacket: readlen=0.
err: RecvPacket: readlen=0.
err: RecvPacket: readlen=0.
linuxrc:choose operation (timeout 4[s])
 1:RamRoot other:HddRoot  ? -HddRoot-
KERNEL:2007/11/3 23:17:32
HDD:2007/6/28 9:42:0
>>> Not expected kernel version, upgrade /etc/linkstation_release
Bypassing CopyFromInitrdToHdd
checking local disk....
fsck 1.27 (8-Mar-2002)
e2fsck 1.27 (8-Mar-2002)
fsck.ext2: Filesystem has unsupported feature(s) (/dev/ls_disk1_1)
e2fsck: Get a newer version of e2fsck!
done
XFS mounting filesystem sda2
Starting XFS recovery on filesystem: sda2 (logdev: internal)
Ending XFS recovery on filesystem: sda2 (logdev: internal)
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 116K
INIT: version 2.86 booting
* .udev/ already exists on the static /dev!
Starting the hotplug events dispatcher: udevdudevd[357]: main: the kernel does not support inotify, udevd cans
.
Synthesizing the initial hotplug events...SAL (ERROR)  0 0 0 :Scsi command completed. pScb c37162c0, ScsiStatD
SAL (ERROR) CDB:12 1 0 0 fe 0
SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
SAL (ERROR)  0 1 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
SAL (ERROR) CDB:12 1 0 0 fe 0
SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
SAL (ERROR)  0 0 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
SAL (ERROR) CDB:12 1 0 0 fe 0
SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
SAL (ERROR)  0 1 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
SAL (ERROR) CDB:12 1 0 0 fe 0
SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
done.
Waiting for /dev to be fully populated...done.
GSetting parameters of disc: (none).
Activating swap:swapon on /dev/sda5
Adding 1004020k swap on /dev/sda5.  Priority:-1 extents:1 across:1004020k
swapon on /dev/sdb5
Adding 1003896k swap on /dev/sdb5.  Priority:-2 extents:1 across:1003896k
.
Setting the system clock..
System Clock set. Local time: Thu Mar 20 20:17:52 UTC 2008.
Cleaning up ifupdown....
Loading device-mapper support.
Generating udev events for MD arrays...done.
Will now check all file systems.
fsck 1.40-WIP (14-Nov-2006)
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.40-WIP (14-Nov-2006)
/dev/sda1: clean, 22/125696 files, 11344/251007 blocks
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
Setting kernel variables...done.
Will now mount local filesystems:mount: none already mounted or /dev/pts busy
mount: according to mtab, devpts is already mounted on /dev/pts
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs: journalled quota options not supported.
EXT3-fs: journalled quota options not supported.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
 failed!
Will now activate swapfile swap:done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
Setting up resolvconf...done.
Setting up networking....
* /etc/network/options is deprecated (see README.Debian of netbase).
Setting up IP spoofing protection...done (rp_filter).
Configuring network interfaces...eth0: link down
done.
Start services: micro_evtd
Starting portmap daemon....
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
Setting console screen modes and fonts.
Starting kernelmon:Initializing random number generator...done.
INIT: Entering runlevel: 2
err: RecvPacket: readlen=0.

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Thu Mar 20, 2008 10:23 pm 
Offline
Regular Member

Joined: Mon Nov 07, 2005 4:37 pm
Posts: 205
Location: Germany
Maybe also for interest - the possible u-boot commands:
Code:
Marvell>> help
?       - alias for 'help'
base    - print or set address offset
board_info   -show board information.
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootend - with micon. send bootend.
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Flash.
buzzer          - with micon. buzzer command.
cmp     - memory compare
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
diskboot- boot from IDE device
echo    - echo args to console
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fan_control     - with micon. fan control  .
fan_rpm         - with micon. fan get rpm.
flinfo  - print FLASH memory information
get_sw          - without micon. get switch status.
go      - start application at address 'addr'
hdd_power       - hdd power control  .
help    - print online help
ide     - IDE sub-system
led             - without micon. call led control routine(for debug).
led_blink       - with micon. led blink control setting.
led_cpu_mcon    - with micon. led cpu micon control setting.
led_on_off      - with micon. led on off control setting.
loop    - infinite loop on address range
md      - memory display
micon           - with micon. command(2byte hex) -data(witin 32byte hex)
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nm      - memory modify (constant address)
pci     - list and access PCI Configuraton Space
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
saveenv - save environment variables to persistent storage
security -device -command -options -password
setenv  - set environment variables
shutdown        - with micon. Poff .
sw_power        - with micon. software power control interface
tftpboot- boot image via network using TFTP protocol
usb_power       - without micon. usb power control  .
version - print monitor version

_________________
LS2 (U-Boot + Freelink) | Kurobox (U-Boot + Deboostraped) | LS Pro Duo (Freelink)


Top
 Profile  
 
 Post subject: Re: Serial @ Pro Duo
PostPosted: Thu Mar 20, 2008 11:54 pm 
Offline
Site Admin
User avatar

Joined: Mon Jul 11, 2005 7:19 am
Posts: 7702
Location: Austria, Vienna
great :)

which means that the cables definitely work for serial read/write access (hehe, the cable i took a picture is bad, it can only read)

can you please download this picture here:
http://buffalo.nas-central.org/index.ph ... _front.jpg

and then use any graphical tool to visually add the pinout there + reupload it to the wiki?

then the next one who wants serial access knows the pinout.

_________________
LS1 (2.6 kernel, foonas svn1062, 750 GB, UBoot 1.2) & LS Pro (FreeLink/jtymod/GenLink, changes all the time)
Thx to all donators!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4  Next

All times are UTC [ DST ]


Who is online

Users browsing this forum: No registered users and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:

Protected by Anti-Spam ACP
Protected by Anti-Spam ACP Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group