Buffalo NAS-Central Forums

Welcome to the Linkstation Wiki community
It is currently Sun Nov 19, 2017 4:11 am

All times are UTC+01:00




Post new topic  Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Fri Jul 16, 2010 1:28 pm 
Offline
Newbie

Joined: Tue Sep 30, 2008 9:02 pm
Posts: 11
Location: Around 2.4 GHz
Hi,

My Kurobox HG with Gentoo Linux doesn't complete the boot anymore but I can enter in the Uboot by using netcat. After booting there's no response from ping or ssh but the netcat tool shows this messages from it:

Code:
Loading 0:1:boot/vmlinux.UBoot

1640597 bytes read

2236 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.23.9
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1640533 Bytes =  1.6 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
   Booting using flat device tree at 0x7f0000
Using Buffalo Linkstation machine description
Linux version 2.6.23.9 (root@joydivision) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 Thu Oct 16 00:52:06 CEST 2008
console [udbg0] enabled
Adding PCI host bridge /soc10x/pci@fec00000
BUFFALO Network Attached Storage Series
(C) 2002-2005 BUFFALO INC.
Zone PFN ranges:
  DMA             0 ->    32768
  Normal      32768 ->    32768
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    32768
Built 1 zonelists in Zone order.  Total pages: 32512
Kernel command line: root=/dev/sda1 netconsole=6666@10.34.71.4/,@10.34.71.6/ rtc-rs5c372.probe=0,0x32
netconsole: local port 6666
netconsole: local IP 10.34.71.4
netconsole: interface eth0
netconsole: remote port 6666
netconsole: remote IP 10.34.71.6
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
Unknown boot option `rtc-rs5c372.probe=0,0x32': ignoring
mpic: Setting up MPIC " EPIC     " version 1.2 at 80040000, max 1 CPUs
mpic: ISU size: 4, shift: 2, mask: 3
mpic: Initializing for 12 sources
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x25
console handover: boot [udbg0] -> real [tty0]
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126320k/131072k available (3168k kernel code, 4592k reserved, 140k data, 99k bss, 152k init)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
PCI: Cannot allocate resource region 5 of device 0000:00:0c.0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x80004500 (irq = 20) is a 16550A
serial8250.0: ttyS1 at MMIO 0x80004600 (irq = 21) is a 16550A
RAMDISK driver initialized: 2 RAM disks of 8192K size 1024 blocksize
loop: module loaded
r8169 Gigabit Ethernet driver 2.2LK loaded
eth0: RTL8110s at 0xc9004c00, 00:0d:0b:ad:98:52, XID 04000000 IRQ 17
netconsole: device eth0 not up yet, forcing it
r8169: eth0: link down
r8169: eth0: link up
console [netcon0] enabled
netconsole: network logging started
sil680: 133MHz clock.
scsi0 : pata_sil680
scsi1 : pata_sil680
ata1: PATA max UDMA/133 cmd 0xfdffbed0 ctl 0xfdffbeda bmdma 0xfdffbef0 irq 18
ata2: PATA max UDMA/133 cmd 0xfdffbee0 ctl 0xfdffbeea bmdma 0xfdffbef8 irq 18
ata1.00: ATA-6: ST3120026A, 8.01, max UDMA/100
ata1.00: 234441648 sectors, multi 0: LBA48
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      ST3120026A       8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 00400000 at ffc00000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 6 MTD partitions on "physmap-flash.0":
0x00000000-0x00300000 : "mtd_firmimg"
0x00300000-0x00370000 : "mtd_bootcode"
0x00370000-0x00380000 : "mtd_status"
0x00380000-0x00400000 : "mtd_conf"
0x00000000-0x00400000 : "mtd_allflash"
0x00310000-0x00400000 : "mtd_data"
usbmon: debugfs is not available
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 19, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 19, io mem 0xbfffe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 19, io mem 0xbfffd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.5
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
rtc-rs5c372 0-0032: setting the system clock to 2010-07-16 04:15:35 (1279253735)
linkstation: disarming the AVR watchdog:
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 152k init

and no more messages. After it frees unused memory, no response. How could I solve this issue?

Greetings :P

_________________
Gentoo Kurobox HG - Uboot 1.2


Top
   
PostPosted: Fri Jul 16, 2010 4:25 pm 
Offline
Site Admin
User avatar

Joined: Sun Jul 17, 2005 4:34 pm
Posts: 5332
Any USB devices connected?


Top
   
PostPosted: Wed Jul 21, 2010 5:36 pm 
Offline
Newbie

Joined: Tue Sep 30, 2008 9:02 pm
Posts: 11
Location: Around 2.4 GHz
andre wrote:
Any USB devices connected?

Any :(

_________________
Gentoo Kurobox HG - Uboot 1.2


Top
   
PostPosted: Wed Jul 21, 2010 9:26 pm 
Offline
Site Admin
User avatar

Joined: Mon Aug 28, 2006 1:15 am
Posts: 2606
have you thought of tftp-booting it w/ a foonas-em kernel and telnet-ing in, running fsck, etc on the hdd and chekcing your fstab?

also your network settings?

go to foonas.org, see the articles on foonas-em (note differences between lsppchd and lsppchg - regular vs your HG)...

hth,

davy

_________________
LS1 (foonas, nfs, Tranmission & p910nd print server, Firefly for my Roku)
LS-HG500 (Lenny)
Various LS-Pros v1,v2 (unbricked w/ serial & jtag)
KuroPro, LS2 & KuroHG (foonas)
Working on davysweather.dyndns.org lately...

=> wooohooo!
wooohooo!
Unknown command 'wooohooo!' - try 'help'


Top
   
PostPosted: Wed Jul 21, 2010 9:34 pm 
Offline
Newbie

Joined: Tue Sep 30, 2008 9:02 pm
Posts: 11
Location: Around 2.4 GHz
davy_gravy wrote:
have you thought of tftp-booting it w/ a foonas-em kernel and telnet-ing in, running fsck, etc on the hdd and chekcing your fstab?

also your network settings?

go to foonas.org, see the articles on foonas-em (note differences between lsppchd and lsppchg - regular vs your HG)...


Thank you Davy. Is it possible to access to my Kuro's files from Uboot or I need to extract the hard-disk?

_________________
Gentoo Kurobox HG - Uboot 1.2


Top
   
PostPosted: Thu Jul 22, 2010 3:58 pm 
Offline
Site Admin
User avatar

Joined: Mon Aug 28, 2006 1:15 am
Posts: 2606
have a look at this... by tftp-booting your HG, you can use the linux tools in foonas-em to mount your hdd w/o opening up your box.

http://www.foonas.org/index.php/Foonas- ... Boot-lsppc

_________________
LS1 (foonas, nfs, Tranmission & p910nd print server, Firefly for my Roku)
LS-HG500 (Lenny)
Various LS-Pros v1,v2 (unbricked w/ serial & jtag)
KuroPro, LS2 & KuroHG (foonas)
Working on davysweather.dyndns.org lately...

=> wooohooo!
wooohooo!
Unknown command 'wooohooo!' - try 'help'


Top
   
PostPosted: Wed Jun 15, 2011 11:17 pm 
Offline
Total Newbie

Joined: Thu Nov 05, 2009 8:54 pm
Posts: 2
Hi,

after some years I want to recover my old Kurobox. I can connect the Kurobox HD to my Desktop PC, but what can I check (/etc/fstab...)?

If I don't discover any bug, is it possible to install an updated Gentoo or another Linux for Kurobox HG with U-boot?

Update: after trying to get into EM mode:
Code:
=> run emboot
run emboot
## Booting image at ffc00000 ...

******* Product Information *******
----------------------------------
Product Name: HD-HGLAN(IEMITSU)
         VER: 2.08
        Date: 2006/2/9 12:0:6
----------------------------------
Verifying checksum... OK
Uncompressing kernel...done.
Loading Ramdisk at 0x07C6C000, end 0x07E6E31A ... OK
Booting the kernel

and it waits ad infinitum...


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 7 posts ] 

All times are UTC+01:00


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Powered by phpBB® Forum Software © phpBB Limited