Buffalo NAS-Central Forums
http://forum.buffalo.nas-central.org/

No internet access from openlink 0.73b
http://forum.buffalo.nas-central.org/viewtopic.php?f=2&t=23737
Page 1 of 1

Author:  jissa [ Thu Jul 21, 2011 11:32 pm ]
Post subject:  No internet access from openlink 0.73b

I updated my LS1 to openlink0.73b and went ahead and added my router ip to resolv.conf to connect the linkstation to the Internet as described in http://buffalo.nas-central.org/wiki/The_LinkStation_firmware_flasher. I still can't get access to the Internet. I tried to get a package using wget and I get "[140.211.169.172]:80 failed: Network is unreachable". I checked the IP address of http://downloads.nas-central.org by pinging from my Windows machine and I get the same IP address.

I also tried to run ntpdate to update the clock but it fails so my guess is that I can't get my LS1 on the Internet.

Do I need to make any changes to my router.

Thank you

Author:  andre [ Fri Jul 22, 2011 5:44 am ]
Post subject:  Re: No internet access from openlink 0.73b

Are you on DHCP or a static IP address? What do "ifconfig" and "cat /etc/resolv.conf" yield?

Author:  jissa [ Fri Jul 22, 2011 6:54 am ]
Post subject:  Re: No internet access from openlink 0.73b

I'm using static IP address and this is my ifconfig and resolv.conf

    eth0 Link encap:Ethernet HWaddr 00:07:40:A4:C8:8D
    inet addr:192.168.0.55 Bcast:192.168.0.255 Mask:255.255.255.0
    EtherTalk Phase 2 addr:65280/241
    UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1
    RX packets:31262 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1485 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0
    RX bytes:5062032 (4.8 Mb) TX bytes:237078 (231.5 Kb)

    eth0:20 Link encap:Ethernet HWaddr 00:07:40:A4:C8:8D
    inet addr:192.168.11.150 Bcast:192.168.11.255 Mask:255.255.255.0
    UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    EtherTalk Phase 2 addr:0/0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    #
    # resolv.conf This file is the resolver configuration file
    # See resolver(5).
    nameserver 192.168.0.1
    nameserver 217.115.138.24

Author:  andre [ Fri Jul 22, 2011 11:00 am ]
Post subject:  Re: No internet access from openlink 0.73b

OK, so your router seems to be 192.168.0.1. Also in your /etc/network/interfaces ("cat /etc/network/interfaces"?

Author:  jissa [ Fri Jul 22, 2011 6:55 pm ]
Post subject:  Re: No internet access from openlink 0.73b

I found the problem. I did not have the gateway setup correctly.

I have another question related to ntp. I setup my timezone using tzconfig and it added America/Los_Angeles to /etc/timezone. I also updated the ntp.conf to point to ntp.org but whenever I run ntpdate I get the message no servers can be used, exiting. if I run
    ntpdate 0.pool.ntp.org
I get a good time sync. Does ntp.conf need to be executable?

Thank you

Page 1 of 1 All times are UTC+01:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/