U-Boot 1.1.4 w/ basic netconsole is now working on my KuroPro ...
This along w/ a kernel that has netconsole turned on seems to work pretty well...
thanks to bbradley who (as usual) provided me with a hint/insight that saved me hours or days in remedying a small problem that stopped the build...
patched source is here :
http://buffalo.nas-central.org/download ... sic.tar.gzI can put the covers back on my machines now...
Code:
egiga0
[PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
switched to TFTP boot.
<<system_bootend>>
Hit any key to stop autoboot: 0
=>
=>
=> print
print
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
serverip=192.168.11.149
boot-em=setenv bootargs console=ttyS0,115200;nboot 0x00100000 0 0x01000000; bootm 0x00100000
enaWrAllo=no
buffalo_ver=BOOTVER=1.091
build_time=18:17:19
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=netconsole=6666@192.168.11.150/,@192.168.11.149/
bootargs_root=root=/dev/mtdblock2 rw panic=5
autoload=no
stdin=nc
stdout=nc
stderr=nc
netmask=255.255.255.0
ncip=192.168.11.149
nc=setenv stdin nc;setenv stdout nc;setenv stderr nc
ser=setenv stdin serial;setenv stdout serial;setenv stderr serial
envfoohdd1=setenv bootcmd 'ide reset; ext2load ide 0:1 0x00100000 /boot/uImage; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda1 rw ;bootm 0x00100000'
envfoohdd2=setenv bootcmd 'ide reset; ext2load ide 0:1 0x00100000 /uImage; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda2 rw ;bootm 0x00100000'
envfooem=setenv def_tftp 'tftp 0x00800000 uImage_em-kuro ; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/ram0 rw ; bootm 0x00800000'
fooboot=ide reset; ext2load ide 0:1 0x00100000 /boot/uImage; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda1 rw ;bootm 0x00100000
foobootem=tftp 0x00800000 uImage_em-kuro ; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/ram0 rw ; bootm 0x00800000
keepalive=micon -0x01 -0x35
envreset=protect off fffff000 ffffffff ; erase fffff000 ffffffff ; protect on fffff000 ffffffff
bootargs=$(bootargs_base) $(bootargs_root) $(buffalo_ver)
nand_uImage_offset=20000
default_kernel_addr=0x00100000
default_initrd_addr=0x02000000
nand_boot=yes
def_tftp=tftp 0x00800000 uImage_em-kuro ; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/ram0 rw ; bootm 0x00800000
ethaddr=00:16:01:A4:E5:5A
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
force_tftp=1
bootcmd=tftp 0x00800000 uImage_em-kuro ; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/ram0 rw ; bootm 0x00800000
Environment size: 2254/4092 bytes
=> run envfoohdd2
run envfoohdd2
=> saveenv
saveenv
Saving Environment to Flash...
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
=> print bootcmd
print bootcmd
bootcmd=ide reset; ext2load ide 0:1 0x00100000 /uImage; setenv bootargs netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda2 rw ;bootm 0x00100000
=> reset
reset
=> egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: ST3808110AS Firm: 3.ADH Ser#: 5LR4TDD3
Type: Hard Disk
Supports 48-bit addressing
Capacity: 76293.9 MB = 74.5 GB (156250000 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage
2322728 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.25.6
Created: 2008-06-15 18:08:06 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2322664 Bytes = 2.2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
arg:netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda2 rw
Linux version 2.6.25.6 (davygravy@bitbaker-i686) (gcc version 4.2.2) #1 PREEMPT Sun Jun 15 13:07:56 CDT 2008
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
Machine: Buffalo/Revogear Kurobox Pro
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda2 rw
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [tty0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125056KB available (4328K code, 257K data, 148K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 236 bytes
NET: Registered protocol family 16
Orion ID: MV88F5182-A2. TCLK=166666667.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 977, nTxLock = 7823
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
MV-643xx 10/100/1000 Ethernet Driver
eth0: port 0 with MAC address 00:16:01:a4:e5:5a
eth0: Scatter Gather Enabled
eth0: TX TCP/IP Checksumming Supported
eth0: RX TCP/UDP Checksum Offload ON
eth0: RX NAPI Enabled
netconsole: local port 6666
netconsole: local IP 192.168.11.150
netconsole: interface eth0
netconsole: remote port 6666
netconsole: remote IP 192.168.11.149
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
netconsole: device eth0 not up yet, forcing it
netconsole: carrier detect appears untrustworthy, waiting 4 seconds
console [netcon0] enabled
netconsole: network logging started
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
sata_mv sata_mv.0: version 1.20
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 29
ata2: SATA max UDMA/133 irq 29
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3808110AS, 3.ADH, max UDMA/133
ata1.00: 156250000 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA ST3808110AS 3.AD PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156250000 512-byte hardware sectors (80000 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156250000 512-byte hardware sectors (80000 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
physmap platform flash device: 00040000 at f4000000
Found: SST 39LF020
physmap-flash.0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
mtd: Giving out device 0 to physmap-flash.0
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 664 at 0x05300000
Creating 5 MTD partitions on "orion_nand":
0x00000000-0x01000000 : "foonas"
mtd: Giving out device 1 to foonas
0x01000000-0x02000000 : "foonas-em"
mtd: Giving out device 2 to foonas-em
0x02000000-0x03000000 : "foonas-iscsi"
mtd: Giving out device 3 to foonas-iscsi
0x03000000-0x05000000 : "foonas-config"
mtd: Giving out device 4 to foonas-config
0x05000000-0x10000000 : "extra"
mtd: Giving out device 5 to extra
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
orion-ehci orion-ehci.1: Marvell Orion EHCI
orion-ehci orion-ehci.1: new USB bus registered, assigned bus number 2
orion-ehci orion-ehci.1: irq 12, io mem 0xf10a0000
orion-ehci orion-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, am/pm, driver version 0.5
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
VFP support v0.3: not present
rtc-rs5c372 0-0032: setting system clock to 2008-06-21 00:36:25 UTC (1214008585)
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 148K
Adding 506008k swap on /dev/sda5. Priority:-1 extents:1 across:506008k
EXT3 FS on sda2, internal journal
_________________
LS1 (foonas, nfs,
Tranmission &
p910nd print server,
Firefly for my
Roku)
LS-HG500 (Lenny)
Various LS-Pros v1,v2 (unbricked w/ serial & jtag)
KuroPro, LS2 & KuroHG (foonas)
Working on
davysweather.dyndns.org lately...
=> wooohooo!
wooohooo!
Unknown command 'wooohooo!' - try 'help'
Login
Register
FAQ
Search
).
