but for me...it works with out any problem.
there is a log capture with putty.
start with stock v1 boot.
note the version string.
log time is my local time,I am from China
Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2008.03.30 05:20:30 =~=~=~=~=~=~=~=~=~=~=~=
Marvell>> reset
Marvell>>
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE
U-Boot 1.1.1 (Jun 12 2006 - 10:32:00) Marvell version: 1.10.8
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Marvell Serial ATA Adapter
Intergrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
switched to TFTP boot.
Hit any key to stop autoboot: 3 0
Marvell>> printenv
bootargs=$(bootargs_base) $(bootargs_root)
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
buffalo_ver=BOOTVER=1.01
build_time=10:35:38
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
def_tftp=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver);bootm 0x00100000 0x00800000
usb0Mode=host
usb1Mode=host
ethact=egiga0
ethaddr=00:16:01:41:f1:b3
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
bootdelay=3
disaMvPnp=no
overEthAddr=no
force_tftp=1
bootcmd=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver);bootm 0x00100000 0x00800000
Environment size: 922/4092 bytes
Marvell>> reset
Marvell>>
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE
U-Boot 1.1.1 (Jun 12 2006 - 10:32:00) Marvell version: 1.10.8
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Marvell Serial ATA Adapter
Intergrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/uImage.buffalo
1751932 bytes read
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-03-28 13:18:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1751868 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-03-28 12:35:08 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4563391 Bytes = 4.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.01
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@server.fasionxgame.com) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #8 Fri Mar 28 21:18:26 CST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.01
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110676KB available (3053K code, 432K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011254)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 1] **
Vendor: SAMSUNG Model: SP2504C Rev: VT10
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c146dba0
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 sda7 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 400000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Platform Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb1: SerialNumber: ehci_platform.4523
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: Product: EHCI Platform Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb2: SerialNumber: ehci_platform.16781
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ehci_platform and address 2
usb 2-1: Product: DSB-650TX USB Ethernet
usb 2-1: Manufacturer: D-Link Corp.
usb 2-1: SerialNumber: 7d3d11
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
pegasus 2-1:1.0: setup Pegasus II specific registers
pegasus 2-1:1.0: eth1, D-Link DSB-650TX, 00:50:ba:7d:3d:11
usbcore: registered new driver pegasus
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
---- in Modified linuxrc ---
Sun Mar 30 05:21:28 JST 2008
err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hit 1 to boot into EM modeCode:
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? 1
-RamdiskRoot-
Freeing init memory: 104K
init started: BusyBox v1.1.1 (2006.06.11-04:13+0000) multi-call binary
Starting pid 253, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
===== exec:checkroot.sh =====
chmod: /home: No such file or directory
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 297160k swap on /dev/ls_disk1_5. Priority:-1 extents:1 across:297160k
create dir : /home
create dir : /var/www
===== exec:create_devlink.sh =====
===== exec:fwupdate.sh =====
umount: /boot: not mounted
mkdir: Cannot create directory `/boot': File exists
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fwupdate.sh:FW not updated
===== exec:sethostname.sh =====
configure files from Buffalo parameters.
===== exec:restore_config.sh =====
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Restore previous configuration files
tar: /boot/conf_save.tgz: No such file or directory
unzip fail.
===== exec:networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
dhcpcd.exe: interface eth0 has been configured with new IP=192.168.11.150
configure files from Buffalo parameters.
===== exec:create_usblink.sh =====
===== exec:kernelmon.sh =====
Starting kernelmon:===== exec:miconmon.sh =====
miconmon 1.00b3 started (Builddate Jun 11 2006 13:14:48)
===== exec:diskmon.sh =====
===== exec:micon_setup.sh =====
===== exec:clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
===== exec:daemonwatch.sh =====
Starting daemonwatch:watch list file : /etc/daemonwatch.list
===== exec:bootcomplete.sh =====
/etc/init.d/bootcomplete.sh: line 9: /etc/init.d/drivecheck.sh: No such file or directory
grep: /etc/linkstation_release: No such file or directory
Starting pid 552, console /dev/ttyS0: '/sbin/getty'
BUFFALO INC. LinkStation series LS-GL(IESADA)
LS-GL-EM1B3 login: root
login[552]: root login on `ttyS0'
sh-2.05b# mount /dev/sda1 /boot
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sh-2.05b# cd /boot
sh-2.05b# ls
boot_options lost+found u-boot.buffalo
hddrootmode pending_standby uImage.buffalo
initrd.buffalo rootfs_ok
linkstation_release system_format
sh-2.05b# vi boot_options
[1;1H[0J[1;1H## Set to YES if not a stock box, comment out if stock box
OTHER_DISTRIBUTION=YES
## Define root path, comment out if stock box
ROOTPATH=/boot
## Advanced use only, specify system area format
SYSTEM_FORMAT="mkfs.xfs -d agcount=4 -l size=32m"
## Set menu timeout (secs), default is 4. Disable, set to 0 or OFF. For
## EM mode set to EM
MENU_TIMEOUT=4
## Set to YES to delete hdd image following update or NO to leave it
REMOVE_HDDROOTFS=YES
## Reset fan as micocontroller does not do this after reboot
miconapl -a fan_set_speed stop
## Watch-dog reset to 250 secs
miconapl -a system_set_watchdog 250
## Clear error LED indication
miconapl -a led_set_code_information clear
## Indicate it ran
miconapl -a bz_imhere 1 b4 a4
~
~
~
~[1;1H[24;1H- boot_options 1/19 5%[0K[1;1H[2;1H[24;1H- boot_options 2/19 10%[0K[2;1H[3;1H[24;1H- boot_options 3/19 15%[0K[3;1H[4;1H[24;1H- boot_options 4/19 21%[0K[4;1H[5;1H[24;1H- boot_options 5/19 26%[0K[5;1H[6;1H[24;1H- boot_options 6/19 31%[0K[6;1H[7;1H[24;1H- boot_options 7/19 36%[0K[7;1H[8;1H[24;1H- boot_options 8/19 42%[0K[8;1H[9;1H[24;1H- boot_options 9/19 47%[0K[9;1H
M[24;1HI boot_options 9/19 47%[0K[9;2H
ME
MEN
MENU[9;6H[9;7H[9;8H[9;9H[9;10H[9;11H[9;12H[9;13H[9;14H[9;15H[9;14H [9;14H[24;1HI boot_options [modified] 9/19 47%[0K[9;14H[9;14He[9;15H[9;14H [9;14H[9;14HE[9;15H[9;15HM[9;16H[9;15H[24;1H- boot_options [modified] 9/19 47%[0K[9;15H[24;1H[0K:WQ wq[9;15H[9;15H[24;1H"boot_options" 19L, 723C[0K[9;15H[24;1H[0Ksh-2.05b# ls
boot_options lost+found u-boot.buffalo
hddrootmode pending_standby uImage.buffalo
initrd.buffalo rootfs_ok
linkstation_release system_format
sh-2.05b#
in pc,use LSUpdater to flush v2's stock uboot,and lspro will reboot
uboot firmware will be flashed at the next bootCode:
Starting pid 580, console /dev/ttyS0: '/etc/init.d/rcDown'
--- rcDown ---
===== exec:shutdown_start.sh =====
called shutdown_start /etc/init.d/shutdown_start.sh
===== exec:shutdown_proc.sh =====
Stop daemonwatch:done.
Stop clientUtil_server:Shutting down FTPD services: killall: proftpd: no process killed
killall: diskmon: no process killed
Stop kernelmon:done.
===== exec:umount_disk.sh =====
killing all servers..
/etc/init.d/umount_disk.sh: line 292: /etc/init.d/smb.sh: No such file or directory
Shutting down FTPD services: killall: proftpd: no process killed
/etc/init.d/umount_disk.sh: line 294: /etc/init.d/atalk.sh: No such file or directory
killing all daemons
Stop daemonwatch:done.
killall: diskmon: no process killed
killall: rsync: no process killed
/etc/init.d/umount_disk.sh: line 410: /etc/init.d/httpd.sh: No such file or directory
killall: sshd: no process killed
\n==== unmounting all disks ====
umount2: Device or resource busy
umount: /dev/sda1: not mounted
umount: /boot: Illegal seek
umount2: Device or resource busy
umount: /dev/sda1 busy - remounted read-only
umount2: Invalid argument
umount: /mnt/disk1/: Illegal seek
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
umount2: Invalid argument
umount: /mnt/usbdisk2: not mounted
umount: /dev/usbdisk1_1: not found
umount: /dev/usbdisk2_1: not found
===== exec:sendsigs.sh =====
Shutting down kernel logger: killall: klogd: no process killed
Shutting down system logger: killall: syslogd: no process killed
Starting pid 624, console /dev/ttyS0: '/bin/umount'
The system is going down NOW !!
Sending SIGTERM to all processes.
Sending SIG
Please stand by while rebooting the system.
Synchronizing SCSI cache for disk sda:
Restarting system.
.
>miconCntl_Reboot
>miconCntl_ShutdownWait
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE
U-Boot 1.1.1 (Jun 12 2006 - 10:32:00) Marvell version: 1.10.8
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Marvell Serial ATA Adapter
Intergrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/uImage.buffalo
1751932 bytes read
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-03-28 13:18:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1751868 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-03-28 12:35:08 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4563391 Bytes = 4.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.01
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@server.fasionxgame.com) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #8 Fri Mar 28 21:18:26 CST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.01
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110676KB available (3053K code, 432K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011254)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 1] **
Vendor: SAMSUNG Model: SP2504C Rev: VT10
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c146dba0
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 sda7 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 400000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Platform Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb1: SerialNumber: ehci_platform.4523
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: Product: EHCI Platform Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb2: SerialNumber: ehci_platform.16781
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ehci_platform and address 2
usb 2-1: Product: DSB-650TX USB Ethernet
usb 2-1: Manufacturer: D-Link Corp.
usb 2-1: SerialNumber: 7d3d11
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
pegasus 2-1:1.0: setup Pegasus II specific registers
pegasus 2-1:1.0: eth1, D-Link DSB-650TX, 00:50:ba:7d:3d:11
usbcore: registered new driver pegasus
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
---- in Modified linuxrc ---
Sun Mar 30 05:23:25 JST 2008
err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
-RamdiskRoot-
Freeing init memory: 104K
init started: BusyBox v1.1.1 (2006.06.11-04:13+0000) multi-call binary
Starting pid 252, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
===== exec:checkroot.sh =====
chmod: /home: No such file or directory
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 297160k swap on /dev/ls_disk1_5. Priority:-1 extents:1 across:297160k
create dir : /home
create dir : /var/www
===== exec:create_devlink.sh =====
===== exec:fwupdate.sh =====
umount: /boot: not mounted
mkdir: Cannot create directory `/boot': File exists
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
linuxrc will flash ubootCode:
exist [u-boot.buffalo.updated]
updating boot...
fwupdate.sh:FW update start
Starting pid 434, console /dev/ttyS0: '/etc/init.d/rcDown'
Starting pid 478, console /dev/ttyS0: '/bin/umount'
The system is going down NOW !!
Sending SIGTERM to all processes.
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
Synchronizing SCSI cache for disk sda:
Restarting system.
.
>miconCntl_Reboot
>miconCntl_ShutdownWait
note the version stringCode:
Orion1 CPU = Low
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1111 phy
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
note this ext2load before tftp mode swithCode:
Using device ide0, partition 1
** Bad partition 1 **
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
switched to TFTP boot.
<<system_bootend>>
Hit any key to stop autoboot: 3 0
Marvell>> printenv
bootargs=$(bootargs_base) $(bootargs_root)
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
ethaddr=00:16:01:41:4E:2B
serverip=192.168.11.149
buffalo_ver=BOOTVER=1.10
buffalo_minor_ver=BOOT_MINOR_VER=1.00
build_time=18:35:39
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
def_tftp=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes;bootm 0x00100000 0x00800000
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
filesize=45A1FF
force_tftp=1
bootcmd=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes;bootm 0x00100000 0x00800000
Environment size: 1004/4092 bytes
show version,then modify bootcmd and save itCode:
Marvell>> version
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
Marvell>> setenv bootcmd anything
Marvell>> saveenv Saving Environment to Flash...
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Marvell>> reset
Marve・rion1 CPU = Low
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1111 phy
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
** Bad partition 1 **
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 1 0
Unknown command '' - try 'help'
Marvell>> printenv
bootargs=$(bootargs_base) $(bootargs_root)
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
ethaddr=00:16:01:41:4E:2B
serverip=192.168.11.149
buffalo_ver=BOOTVER=1.10
buffalo_minor_ver=BOOT_MINOR_VER=1.00
build_time=18:35:39
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
def_tftp=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes;bootm 0x00100000 0x00800000
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
filesize=45A1FF
bootcmd=anything
Environment size: 835/4092 bytes
yes,it changes(bootcmd),confirmed,then restore env param to initial valueCode:
Marvell>> protect off fffff000 fffffffff .
Un-Protected 1 sectors
Marvell>> erase fffff000 ffffffff
.
Erased 1 sectors
Marvell>> protect on fffff000 ffffffff .
Protected 1 sectors
Marvell>> reset
Marvell>> Orion1 CPU = Low
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
-- initialize Env for BUFFALO
*** set ethaddr to initial value
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Using 88E1111 phy
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
** Bad partition 1 **
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 0
Marvell>> printenv
bootargs=$(bootargs_base) $(bootargs_root)
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
stdin=serial
stdout=serial
stderr=serial
cpuName=926
CASset=min
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
MALLOC_len=4
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
buffalo_ver=BOOTVER=1.10
buffalo_minor_ver=BOOT_MINOR_VER=1.00
build_time=18:35:39
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
def_tftp=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes;bootm 0x00100000 0x00800000
bootdelay=3
disaMvPnp=no
ethaddr=00:00:00:00:51:81
overEthAddr=no
usb0Mode=host
usb1Mode=host
ethact=egiga0
filesize=45A1FF
bootcmd=ide reset; ext2load ide 1:1 0x00100000 /$(kernel);ext2load ide 1:1 0x00800000 /$(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver);bootm 0x00100000 0x00800000
Environment size: 1013/4092 bytes
Marvell>> version
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/uImage.buffalo
1751932 bytes read
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-03-28 13:18:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1751868 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-03-28 12:35:08 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4563391 Bytes = 4.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@server.fasionxgame.com) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #8 Fri Mar 28 21:18:26 CST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110676KB available (3053K code, 432K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011254)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 1] **
Vendor: SAMSUNG Model: SP2504C Rev: VT10
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c146fba0
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 sda7 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 400000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Platform Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb1: SerialNumber: ehci_platform.4523
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: Product: EHCI Platform Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb2: SerialNumber: ehci_platform.16781
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ehci_platform and address 2
usb 2-1: Product: DSB-650TX USB Ethernet
usb 2-1: Manufacturer: D-Link Corp.
usb 2-1: SerialNumber: 7d3d11
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
pegasus 2-1:1.0: setup Pegasus II specific registers
pegasus 2-1:1.0: eth1, D-Link DSB-650TX, 00:50:ba:7d:3d:11
usbcore: registered new driver pegasus
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
---- in Modified linuxrc ---
Sun Mar 30 05:26:59 JST 2008
err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
-RamdiskRoot-
Freeing init memory: 104K
init started: BusyBox v1.1.1 (2006.06.11-04:13+0000) multi-call binary
Starting pid 252, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
===== exec:checkroot.sh =====
chmod: /home: No such file or directory
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 297160k swap on /dev/ls_disk1_5. Priority:-1 extents:1 across:297160k
create dir : /home
create dir : /var/www
===== exec:create_devlink.sh =====
===== exec:fwupdate.sh =====
umount: /boot: not mounted
mkdir: Cannot create directory `/boot': File exists
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fwupdate.sh:FW not updated
===== exec:sethostname.sh =====
configure files from Buffalo parameters.
===== exec:restore_config.sh =====
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Restore previous configuration files
tar: /boot/conf_save.tgz: No such file or directory
unzip fail.
===== exec:networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
dhcpcd.exe: interface eth0 has been configured with new IP=192.168.11.2
configure files from Buffalo parameters.
===== exec:create_usblink.sh =====
===== exec:kernelmon.sh =====
Starting kernelmon:===== exec:miconmon.sh =====
miconmon 1.00b3 started (Builddate Jun 11 2006 13:14:48)
===== exec:diskmon.sh =====
===== exec:micon_setup.sh =====
===== exec:clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
===== exec:daemonwatch.sh =====
Starting daemonwatch:watch list file : /etc/daemonwatch.list
===== exec:bootcomplete.sh =====
/etc/init.d/bootcomplete.sh: line 9: /etc/init.d/drivecheck.sh: No such file or directory
grep: /etc/linkstation_release: No such file or directory
Starting pid 551, console /dev/ttyS0: '/sbin/getty'
BUFFALO INC. LinkStation series LS-GL(IESADA)
LS-GL-EM181 login: root
login[551]: root login on `ttyS0'
sh-2.05b# reboot
Starting pid 565, console /dev/ttyS0: '/etc/init.d/rcDown'
--- rcDown ---
===== exec:shutdown_start.sh =====
sh-2.05b# called shutdown_start /etc/init.d/shutdown_start.sh
===== exec:shutdown_proc.sh =====
Stop daemonwatch:done.
Stop clientUtil_server:Shutting down FTPD services: killall: proftpd: no process killed
killall: diskmon: no process killed
Stop kernelmon:done.
===== exec:umount_disk.sh =====
killing all servers..
/etc/init.d/umount_disk.sh: line 292: /etc/init.d/smb.sh: No such file or directory
Shutting down FTPD services: killall: proftpd: no process killed
/etc/init.d/umount_disk.sh: line 294: /etc/init.d/atalk.sh: No such file or directory
killing all daemons
Stop daemonwatch:done.
killall: diskmon: no process killed
killall: rsync: no process killed
/etc/init.d/umount_disk.sh: line 410: /etc/init.d/httpd.sh: No such file or directory
killall: sshd: no process killed
\n==== unmounting all disks ====
umount2: Invalid argument
umount: /boot: Illegal seek
umount2: Invalid argument
umount: /mnt/disk1/: Illegal seek
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
umount2: Invalid argument
umount: /mnt/usbdisk2: not mounted
umount: /dev/usbdisk1_1: not found
umount: /dev/usbdisk2_1: not found
===== exec:sendsigs.sh =====
Shutting down kernel logger: killall: klogd: no process killed
Shutting down system logger: killall: syslogd: no process killed
Starting pid 609, console /dev/ttyS0: '/bin/umount'
The system is going down NOW !!
Sending SIGTERM to all processes.
Sending SIG
Please stand by while rebooting the system.
Synchronizing SCSI cache for disk sda:
Restarting system.
.
>miconCntl_Reboot
>miconCntl_ShutdownWait
Orion1 CPU = Low
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1111 phy
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
** Bad partition 1 **
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
switched to TFTP boot.
<<system_bootend>>
Hit any key to stop autoboot: 3 2 0
Marvell>> printenv
bootargs=$(bootargs_base) $(bootargs_root)
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
buffalo_ver=BOOTVER=1.10
buffalo_minor_ver=BOOT_MINOR_VER=1.00
build_time=18:35:39
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
def_tftp=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes;bootm 0x00100000 0x00800000
ethaddr=00:00:00:00:51:81
ethact=egiga0
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
filesize=45A1FF
force_tftp=1
bootcmd=tftp 0x00100000 $(kernel);tftp 0x00800000 $(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes;bootm 0x00100000 0x00800000
Environment size: 1002/4092 bytes
note bootcmd's value,we save itCode:
Marvell>> saveenv Saving Environment to Flash...
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Marvell>> reset Marvell>> Orion1 CPU = Low
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1111 phy
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
** Bad partition 1 **
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 1 0
Using egiga0 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'uImage.buffalo'.
Load address: 0x100000
Loading: *
TFTP error: 'File not found' (1)
Starting again
error
Abort
yes,confirmed,bootcmd HAS been saved successfully.Code:
Marvell>> protect off ffffff000 ffffffff .
Un-Protected 1 sectors
Marvell>> erase fffff000 ffffffff
.
Erased 1 sectors
Marvell>> protect on fffff000 ffffffff .
Protected 1 sectors
Marvell>> reset Marvell>> Orion1 CPU = Low
=== BUFFALO LS-GL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
-- initialize Env for BUFFALO
*** set ethaddr to initial value
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Using 88E1111 phy
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
** Bad partition 1 **
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
Hit any key to stop autoboot: 3 2 0
Marvell>> version
U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
Marvell>> printenv bootcmd
bootcmd=ide reset; ext2load ide 1:1 0x00100000 /$(kernel);ext2load ide 1:1 0x00800000 /$(initrd);setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver);bootm 0x00100000 0x00800000
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 1: OK
Model: SAMSUNG SP2504C Firm: VT100-50 Ser#: S09QJ1CP211963
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/uImage.buffalo
1751932 bytes read
Using device ide1, partition 1
Loading from block device ide device 1, partition 1: Name: hdb1
Type: U-Boot File:/initrd.buffalo
4563455 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-03-28 13:18:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1751868 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-03-28 12:35:08 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4563391 Bytes = 4.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@server.fasionxgame.com) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #8 Fri Mar 28 21:18:26 CST 2008
yes,after restore evn param to initial value,kernel booted.
the kernel is cross compiled using gpl source linux-2.6.16_lsp.1.7.8.tar.gz
server.fasionxgame.com is my company's gateway server running fedora core 7... 
Code:
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110676KB available (3053K code, 432K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011254)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 1] **
Vendor: SAMSUNG Model: SP2504C Rev: VT10
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c146dba0
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 sda7 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 400000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Platform Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb1: SerialNumber: ehci_platform.4523
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: Product: EHCI Platform Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb2: SerialNumber: ehci_platform.16781
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ehci_platform and address 2
usb 2-1: Product: DSB-650TX USB Ethernet
usb 2-1: Manufacturer: D-Link Corp.
usb 2-1: SerialNumber: 7d3d11
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
pegasus 2-1:1.0: setup Pegasus II specific registers
pegasus 2-1:1.0: eth1, D-Link DSB-650TX, 00:50:ba:7d:3d:11
usbcore: registered new driver pegasus
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
---- in Modified linuxrc ---
Sun Mar 30 05:30:25 JST 2008
err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
-RamdiskRoot-
Freeing init memory: 104K
init started: BusyBox v1.1.1 (2006.06.11-04:13+0000) multi-call binary
Starting pid 252, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
===== exec:checkroot.sh =====
chmod: /home: No such file or directory
mkdir: Cannot create directory `/var/lock': File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 297160k swap on /dev/ls_disk1_5. Priority:-1 extents:1 across:297160k
create dir : /home
create dir : /var/www
===== exec:create_devlink.sh =====
===== exec:fwupdate.sh =====
umount: /boot: not mounted
mkdir: Cannot create directory `/boot': File exists
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fwupdate.sh:FW not updated
===== exec:sethostname.sh =====
configure files from Buffalo parameters.
===== exec:restore_config.sh =====
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Restore previous configuration files
tar: /boot/conf_save.tgz: No such file or directory
unzip fail.
===== exec:networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
dhcpcd.exe: interface eth0 has been configured with new IP=192.168.11.2
configure files from Buffalo parameters.
===== exec:create_usblink.sh =====
===== exec:kernelmon.sh =====
Starting kernelmon:===== exec:miconmon.sh =====
miconmon 1.00b3 started (Builddate Jun 11 2006 13:14:48)
===== exec:diskmon.sh =====
===== exec:micon_setup.sh =====
===== exec:clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
===== exec:daemonwatch.sh =====
Starting daemonwatch:watch list file : /etc/daemonwatch.list
===== exec:bootcomplete.sh =====
/etc/init.d/bootcomplete.sh: line 9: /etc/init.d/drivecheck.sh: No such file or directory
grep: /etc/linkstation_release: No such file or directory
Starting pid 551, console /dev/ttyS0: '/sbin/getty'
BUFFALO INC. LinkStation series LS-GL(IESADA)
LS-GL-EM181 login: root
login[551]: root login on `ttyS0'
sh-2.05b#
YES,from the log,you can see there is NO problem with saving env param.
Register
Login
FAQ
Search
...
I still need to tweak the bootdelay ... and maybe one or two minor changes to improve the performance...
